Found this on the internet in 5 seconds or less. Its not % clear whether its a bottom view of the device or top side view of the socket, you can determine that in . A relay is an electrically operated switch. Many relays use an electromagnet to operate a switching mechanism, but other operating principles are also used. JQC-3FC(T73) DC12V pinouts. A relay is an electrically activated switch. It consists of a coil internally which will creates a magnetic field that.

Author: Mogar Dailmaran
Country: Italy
Language: English (Spanish)
Genre: Career
Published (Last): 27 September 2017
Pages: 68
PDF File Size: 13.12 Mb
ePub File Size: 15.41 Mb
ISBN: 218-5-61677-752-9
Downloads: 17722
Price: Free* [*Free Regsitration Required]
Uploader: Mezilrajas

Wiring for power relay jqc-3fc t73 dc5v Ask Question. Choosing IC with EN signal 2. Originally Posted by immadi. Please tell me in that way which pin connected where. Thank you very much for your reply, I will try to do so. You need a general-purpose NPN transistor with its emitter to ground, it collector switching one side of the relay coil with the other side going to whatever voltage you need to power it, and the base supplied from an Arduino pin via a Ohm resistor.

I would like everything to work on one power supply.

Relays CRT JQC-3FC(T73) DC12V T73-1C-12V

The time now is The transistor drives the relay control coil coil1 and coil2 pins I don’t see the problem. No, don’t apologise, but if you want sensible answers, post a Jqd-3fc link to the thing you are talking about.

You also need a diode across the relay coil, anode to the transistor collector and cathode to the supply.

Thank you in advance! Equating complex number interms of the other 6. Relay jqc-3f, connect to the arduino.

  ESPECTROFOTOMETRIA UV VISIVEL PDF

Thank you in advance! Turn the relay upside down so that you are facing the pins not the plastic cover side, then it is easy to figure the pins since one side has three and iqc-3fc other side two.

I agree – I would solder a wire to the relay and insulate with heat-shrink tubing, then put the other end of the wire in the brass thing, ideally located in t3 plastic box so that it can’t be touched. Anyone know the IR jwc-3fc TV pin description??? The brass thing will be carrying v ac. Thank you very much for your reply, I will try to do so. No, don’t apologise, but if you want sensible answers, post a Web link to the thing you are talking about.

CMOS Technology file 1.

I apologize for my English. It’s just not very convenient, because will have to make separate meals PV charger battery circuit 4.

Part and Inventory Search. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Heat sinks, Part 2: Digital multimeter appears to have measured voltages lower than expected. I have read that if Arduino submit 12V, and they will be available at the outlet, do not want to burn the card check this out Turn on power triac – proposed circuit analysis 0.

PNP transistor not working 2. How can the power consumption for computing be reduced for energy harvesting? Dec 248: My relay has 5 pins,one side 3 pins and another side 2 pins. You need a general-purpose NPN transistor with its emitter to ground, it collector switching one side of the relay coil with the other side going to whatever voltage you need to power it, and the base supplied from an Arduino pin via a Ohm resistor.

  LOST AND FOUND HALFFAST PDF

Show you how you can connect a jcq-3f relay to the Arduino, so I did not face even in theory. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

In connecting that am facing problem about where to connect those pins. ModelSim – How to force a struct type written in SystemVerilog?

Just need to find a relay jqc-3f 5 volts. Similar Threads how to make 8 pin relay using two 5 pin relays 6. The jumpers carry DC.

Distorted Sine output from Transformer 8. The wooden box will be used to contain the relay and ac lines. Sign up or log in Sign up using Google.

please tell me the pin description of a 12v relay

Jq-c3fc would suggest you try the circuit either with a small low voltage lamp or with a led and a low voltage source until it is tested to work properly, then if you want you can use a mains kqc-3fc. Link up manifnst of the relay. Read times previous topic – next topic. Thank you, so clear, once again thank you for your help! I would like everything to work on one power supply. Please don’t make requests for help in private using PM.

Losses in inductor of a boost converter 9.