FYI, If you decide to attempt any modifications to your HTX, you are doing so at your own risk. HTX Owners Manual HTX/Albrecht AE Service. Update*** I’m still doing this repair for those who may need it. Here are the specifics. I charge a flat fee of $35 which includes the new mic cord, the. Cat. No. OWNER’S MANUAL HTX TWO-METER MOBILE TRANSCEIVER Please read before using this transceiver. INTRODUCTION Your .

Author: Vudotaxe Faull
Country: Botswana
Language: English (Spanish)
Genre: Life
Published (Last): 10 June 2004
Pages: 223
PDF File Size: 6.5 Mb
ePub File Size: 20.26 Mb
ISBN: 680-7-37903-463-4
Downloads: 40336
Price: Free* [*Free Regsitration Required]
Uploader: Kajilabar

When a repeater uses a subaudible tone, it does not react to any transmission that does not include that tone. Scan delay delay before resume when 2. If squelch is off, the transceiver stops on each location for about 1 sec- ond.

Repeater Operation Operation through a repeater, where you transmit on one frequency and receive on another, is called duplex operation. Your HTX includes all 38 standard subaudible tones. Turning Auto Manal On and Off The HTX can automatically select the correct duplex offset for frequencies normally assigned to repeaters and selects no offset simplex for other frequencies.

Setting the Scanning Range. Tuning to a Frequency 1.

RADIO SHACK HTX OWNER’S MANUAL Pdf Download.

The HTX continues auto store until all memories are used. Hold the microphone about 3 htx-522 from your mouth. Be sure T-SQL is not on the display. Press F, then press MR. Cr —resume after carrier drops.

Index of /k/kb1uif/downloads/Service & User Manuals/Radio Shack/HTX-252

Then press MR to save all settings. If you do not want a transmit tone, select oFF. Activating Subaudible Tone Transmit and Squelch 1. Important notes in this manual have a large exclamation mark!

  COMO PUEDO DESPROTEGER UN ARCHIVO DE PDF

If the HTX does not turn on, even when you are sure the power wire is properly connected to a 12V DC power source, check the fuse and replace it, if necessary. May or may not be the case but drill at your own risk. Follow these steps to change the look-back time. This standard set of tones is used by many different amateur radio systems for accessing programmable features and dialing through autopatches.

Scanning for a Frequency 1.

Radio Shack HTX-252 Microphone Cord Replacement

To store the frequency in a standard memory, press F. Replace the fuse in the holder and snap it closed. Your local RadioShack store has a wide selection htxx-252 which to choose. The new frequency ranges are: Setting the Power Level. Spam Blocked 9, spam blocked by Akismet. Press T-SQL a third time to turn off both subaudible tone transmit and squelch.

It will slip off of the old cable without any problem but getting it to fit the new thicker cable takes a little work. Mount the base station antenna according to its instructions. Checking Priority Channel 1. Using the Menu—lists the options in the configuration menu and gives the page numbers where the options are discussed.

You can set the transceiver to stop transmitting and sound a beep if a single transmission exceeds the selected time none, 1, 2, 3, 5, 7, 10, or 15 minutes. This special tone lets you listen only to oth- er transceivers set to the same tone frequency maual you use the transceiver in simplex operation.

  EQS746 CLARION PDF

Luckily all of the conductors get soldered right next to each other. Subaudible Tone Frequencies Hz Then, while holding down PTT, press the digits on the microphone to transmit the tones.

Radio Shack HTX Owner`s manual |

Follow these steps to use the menu: To turn the transceiver off, rotate counterclockwise until it clicks. Press VFO and tune to a frequency you want to store. I also recommend using a flux to help in flowing the solder. For example, to enter Using the holder as a tem- plate, mark the position for the mounting screw holes at the desired location. Use mnual supplied screws, metal washers, bracket, rubber washers, and mounting knobs, as shown, to mount the transceiver.

LOCK To return to the standard frequency range, repeat the above pro- cedure. Warranty does not cover transportation costs. Repeatedly press scan setting. This gives users of low-power transceivers the ability to communicate over a much greater range. Individually Programmable Repeater Offsets —let you program different repeater offset frequencies for each memory, and a default repeater offset for manually-tuned frequencies. If the tones match, it operates as if it received the hhtx-252 sequence.

Follow these steps manuzl turn on auto-reply.