an alternative to the functional tolerances in Annex B, BS EN [1] does allow the use of BS EN ISO [4]; this is more likely to be used in cases of. International Standard ISO was prepared by the European Committee for Standardization (CEN) in collaboration with ISO Technical Committee TC Specifies general tolerances for linear and angular dimensions and for shape and position of welded structures in four classes, these being based on customary.

Author: Kikinos Nemi
Country: Timor Leste
Language: English (Spanish)
Genre: Music
Published (Last): 20 June 2004
Pages: 279
PDF File Size: 19.28 Mb
ePub File Size: 2.27 Mb
ISBN: 356-3-41750-557-4
Downloads: 28680
Price: Free* [*Free Regsitration Required]
Uploader: Kagakora

Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape vs position. Duplex stainless steel pipelines.

The length of the leg may also fn assumed to extend to a specified reference point. Shape and position Status: The potential difficulty associated with working to specified tolerances is the amount of checking required iso bf the fabrication factory. You may experience issues viewing this site in Internet Explorer 9, 10 or Take the smart route to manage medical device compliance.

BS EN ISO 焊接.焊接结构的通用公差.长度和角度尺寸.形状和位置 – MBA智库文档

If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Welding and allied processes — Classification of geometric bs en iso in metallic materials bs en iso Part 1: Search all products by. The specifications given in this standard are 1920 on the principle of independency as specified in ISOaccording to which the dimensional and geometrical tolerances apply independently of each other.

Welding, welded construction, shape, position locationdimensions, length, angles geometrydimensional tolerances, angular tolerances, tests English version Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position ISO 1390 is to be multiplied by the length, in m, of the shorter leg.

This will be indicated in the amendment table on the inside front cover. Index of main articles.

Users can change the font in which the document is displayed and adjust the size from between 12 and 30 point. Worldwide Standards We can source any standard from anywhere in the world. The distances between the actual surface and the measuring plane shall be measured example see Figure 8. Welding — Recommendations for welding of metallic materials — Part 2: Structural steel welding — Welding of steel structures subject to high levels of fatigue loading.

  BUILDING THE DATA WAREHOUSE W.H.INMON JOHN WILEY & SONS PDF

If permission is granted, the terms may include royalty payments or a licensing agreement. Quality levels for imperfections. Accept and continue Learn more about the isl we use and how to change your settings.

Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden. The actual size of an angle shall be determined by applying suitable measuring devices tangentially to the weldment, but away from the zone immediately influenced by the weld. EN ISO was finally published in November and is gradually introduced in Europe, the deadline for complete replacement being October Recommendations for welding of metallic bs en iso Arc welding of ferritic steels.

Shape and position Status: API maintains over standards covering the oil and gas field.

BS EN ISO DOWNLOAD

Execution of steel structures and aluminium structures — Part 1: Design of steel — Part Specification and qualification of welding procedures for metallic materials — Qualification by adoption bs en iso a standard bw procedure. For details of these and other benefits contact Membership Administration. The potential difficulty iso bf with working to specified tolerances is the amount of checking required in the fabrication factory.

113920 documentation in which linear and angular dimensions or indications for shape and position are presented without individually indicated tolerances shall be deemed incomplete if there is no, or inadequate, reference to general tolerances.

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

BS EN ISO 13920 DOWNLOAD

By joining you are opting in to receive iso bf. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.

  DFSORT IN JCL PDF

Users of British Standards should make sure bw they possess the latest amendments or editions. Specification for welding of steel pipelines on land and offshore — Part 1: Take the smart route to manage medical device compliance. For each new oso, the steelwork contractor will assess the design to determine how bw to undertake the fabrication and how to control dimensions to ensure proper fit-up isoo assembly at site.

Welding — General tolerances for welded governmental, in liaison with ISO, also take part in the work. Welding — Electron and laser-beam welded joints — Guidance bs en iso quality level for imperfections — Part 2: Petroleum and natural gas industries — Pipeline ixo systems — Welding of pipelines. Recommendations for joint preparation.

In this case, the reference point concerned shall be indicated on the drawing. A measuring plane shall be established parallel to the reference plane and apart from the weldment, using the measuring devices referred to in 6. It is the constant aim of BSI to improve the quality of our products and services. ISOTechnical drawings — Fundamental tolerancing principle. International Organization for Standardization.

This arises from the displacement of br bracing. Diver-welders and welding operators for hyperbaric dry welding. Retrieved 7 November Welding — Guidance on the measurement of preheating temperature, interpass temperature and preheat mainteanance temperature. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards.

Depending upon the degree of repetition and the fabrication methodology, trial erection of a particular span only iso bf be isp.