3com SuperStack 3 T Pdf User Manuals. View online or download 3com SuperStack 3 T Getting Started Manual, Datasheet. User manual for the device 3Com SUPERSTACK T. Online user manual database. Get 3Com SUPERSTACK T Switch User Manual. Get all 3Com manuals!.
|Published (Last):||27 October 2006|
|PDF File Size:||3.26 Mb|
|ePub File Size:||16.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
The conditions are only maintained ifthe equipment to which it is connected also operates under SELVconditions. As soon as a network connection is made the Switch begins the automatic IP configuration process. Damagecaused to the unit by using incorrect screws invalidates your warranty. Accessing Online Documentation About The Switch Family These are shielded RJ data sockets.
This section applies to the SuperStack 3 Switch G only. Air-flow is not restricted around the Switch or through the vents in the side of the Switch. Thewhole setup process is summarised in Figure 8. Attach a male duplex SC connector on the network cable into the duplexSC connector on the transceiver. Switch t 3c This software allows you to communicate with the Switch via the console port directly, or through a modem. Connecting A Redundant Power System Only connect RJ data connectors, network telephony systems, or network telephones to these sockets.
Marlborough, MA 3Com Technologies reserves the right to revise this documentation and to make changes in content from Summary of the content on the page No.
You can find pin-out diagrams for both cables in Appendix B on page Only connect RJ dataconnectors, network telephony systems, or network telephones to thesesockets. Table 3 Hardware features Installing The Switch From the Help menu, select Contents.
It covers the following topics: Static IP addresses are necessary to ensure that the Switch is always allocated the same IP information. Table of contents Getting Started Guide If the login prompt does not display immediately, press Return a few times until it starts.
If you want to make a connection to another MDIXport, you need a mxnual cable.
3com SuperStack 3 T Manuals
Passwords command line interface, or to change the default passwords, you need manuaal log in with a valid user name and password. Warnings contain directions that you must follow for yourpersonal safety. If installing the Switch Series unit in a stack with SuperStack II or SuperStack 3 units that are narrower than the Series, the Switch Series unit must be installed below the narrower units.
The unit LEDs will display the unit number in the stack, from 1 at the bottom to 4 at maunal top. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
3Com SuperStack 3 4226T Manuals
Redundant Power To protect against internal power supply failure, you can use this socket A Safety Information You must read the following safety information before carrying out any installation or removal of components, or any maintenance procedures on the Switch Series. Because the speedand duplex modes are fixed by the media type, only the flow control isnegotiated with the link partner.
Switch g 3c Choosing A Suitable Site Use the following sequence of steps to activate the GBIC ports. Solving Communication Problems Don’t have an account? Use of controls or adjustments of performance orprocedures other than those specified herein may result in hazardouslaser emissions. Detailed procedural stepsare contained in the sections that follow.
To manage a Switch using the command line interface over a network the Network using Telnet: Page 43 1 Connect the workstation to the console port using a standard null modem cable as shown in Figure 13 Connecting a workstation to the Switch via the console port To connect the cable: Page 37 The final page displays a summary of the information entered. These are shielded RJ data sockets. Methods Of Managing A Switch Solving Stack Formation Problems If your IP network is internal to your organization only, that is, you do not access the Internet, you may use any arbitrary IP address as long as it is not being used by another device on your network.
Choosing The Correct Fiber Cables By pressing ‘print’ button you will print only current page. About This Guide You can do this using the Web interface or the command line interface CLI via telnet.
Summary of the content on the page No. The whole setup process is summarised in are contained in the sections that follow.
SC connector on the transceiver. Installation and removal of the unit must be carried out byqualified personnel only. If your IP network is internal to your organization only, that is, you do not access the Internet, you may use any arbitrary IP address as long as it is not being used by another device on your network.
You must do this whilst the Switch is offline, that is, before you connect the Switch to a network.